HAL options after Windows XP or Windows Server 2003 Setup (309283)

MORE INFORMATION

Windows XP Device Manager and Windows Server 2003 Device Manager list limited choices for changing your HAL type when you click Update Driver. Microsoft Windows 2000 Device Manager lets you select any HAL type. If you select an incorrect HAL, you may not be able to start Windows 2000, or you may have other issues.Although the selections are now limited, you should change the HAL only if you are sure that the selected HAL works on your system. The options that are presented here are known to be compatible with most systems. However, a few systems may experience problems.

When you install the following HALs on a Windows XP-based or Windows Server 2003-based computer, the following device manager HAL options appear:

"Standard PC", Non-ACPI PIC HAL (Hal.dll)

• Standard PC

"MPS Uniprocessor PC", Non-ACPI APIC UP HAL (Halapic.dll)

• Standard PC
• MPS Uniprocessor
• MPS Multiprocessor

"MPS Multiprocessor PC", Non-ACPI APIC MP HAL (Halmps.dll)

• Standard PC
• MPS Multiprocessor

"Advanced Configuration and Power Interface (ACPI) PC", ACPI PIC HAL (Halacpi.dll)

• Standard PC
• Advanced Configuration and Power Interface (ACPI) PC

"ACPI Uniprocessor PC", ACPI APIC UP HAL (Halaacpi.dll)

• Standard PC
• Advanced Configuration and Power Interface (ACPI) PC
• ACPI Uniprocessor
• ACPI Multiprocessor

"ACPI Multiprocessor PC", ACPI APIC MP HAL (Halmacpi.dll)

• Standard PC
• Advanced Configuration and Power Interface (ACPI) PC
• ACPI Multiprocessor
• MPS Multiprocessor

Notes

1. A common symptom when deploying the incorrect image to a computer is that the Sysprep image stops responding on restart or reports the following error message:
   Stop 0x0000007b
2. If an incorrect HAL is forced during Setup or by using a System Preparation Image (Sysprep), you can see the correct list of HALs only if you perform a new installation of Windows XP or Windows Server 2003. You cannot change to a HAL other than what is listed in Device Manager.
3. Device Manager does not permit the change from a Non-ACPI HAL to an ACPI HAL. You must use a new install of Windows XP or Windows Server 2003 for this kind of change. Change from an ACPI HAL to a Non-ACPI HAL only for troubleshooting purposes.
4. On Windows XP and later versions, the ACPI Uniprocessor HAL and the MPS Uniprocessor HAL recognize the existence of more than one processor and report the MP ID. Plug and Play detects that the computer devnode's hardware ID list has changed and moves the devnode back through the "found new hardware" detection process. Therefore, when you add a second processor, the MP files (HAL and kernels) are automatically installed, and you do not have to manually update the driver in Device Manager.
5. Microsoft does not support running a HAL other than the HAL that Windows Setup would typically install on the computer. For example, running a PIC HAL on an APIC computer is not supported. Although this configuration may appear to work, Microsoft does not test this configuration and you may have performance and interrupt issues. Microsoft also does not support swapping out the files that are used by the HAL to manually change HAL types.
6. Microsoft recommends that you switch HALs for troubleshooting purposes only or to workaround a hardware problem.
7. When you create a Sysprep image, the image must contain the correct HAL type for the target computer. The following list describes the computers that you can deploy a particular Sysprep image to based on the HAL type in the source computer:
   • You can deploy a Sysprep image created on a computer that uses a Standard PC, Non-ACPI PIC HAL (Hal.dll) to a computer that uses the following HAL types:
     • Standard PC, Non-ACPI PIC HAL (Hal.dll)
   • You can deploy a Sysprep image created on a computer that uses an Advanced Configuration and Power Interface (ACPI) PC, ACPI PIC HAL (Halacpi.dll) to a computer that uses the following HAL types:
     • Advanced Configuration and Power Interface (ACPI) PC, ACPI PIC HAL (Halacpi.dll)
   • You can deploy a Sysprep image created on a computer that uses a MPS Uniprocessor PC, Non-ACPI APIC UP HAL (Halapic.dll) to a computer that uses the following HAL types:
     • MPS Uniprocessor PC, Non-ACPI APIC UP HAL (Halapic.dll)
     • MPS Multiprocessor PC, Non-ACPI APIC MP HAL (Halmps.dll)
   • You can deploy a Sysprep image created on a computer that uses a MPS Multiprocessor PC, Non-ACPI APIC MP HAL (Halmps.dll) to a computer that uses the following HAL types:
     • MPS Multiprocessor PC, Non-ACPI APIC MP HAL (Halmps.dll)
     • MPS Uniprocessor PC, Non-ACPI APIC UP HAL (Halapic.dll)
   • You can deploy a Sysprep image created on a computer that uses an ACPI Uniprocessor PC, ACPI APIC UP HAL (Halaacpi.dll) to a computer that uses the following HAL types:
     • ACPI Uniprocessor PC, ACPI APIC UP HAL (Halaacpi.dll)
     • ACPI Multiprocessor PC, ACPI APIC MP HAL (Halmacpi.dll)
   • You can deploy a Sysprep image created on a computer that uses an ACPI Multiprocessor PC, ACPI APIC MP HAL (Halmacpi.dll) to a computer that uses the following HAL types:
     • ACPI Multiprocessor PC, ACPI APIC MP HAL (Halmacpi.dll)
     • ACPI Uniprocessor PC, ACPI APIC UP HAL (Halaacpi.dll)

Note Currently, the options in Device Manager do not list an APIC version of the HAL when you change the HAL on an APIC system. Although the PIC HAL that is installed may work, you can select the preferred APIC version after you install a hotfix for computers that are running Windows Server 2003 with Service Pack 1.

For more information about the hotfix for Windows Server 2003 Service Pack 1, click the following article number to view the article in the Microsoft Knowledge Base: