RAS Err Msg Connecting a Remote Server Share: Access Denied (131659)


The information in this article applies to:

  • Microsoft Windows for Workgroups 3.11
This article was previously published under Q131659

SYMPTOMS

When you try to connect to a remote resource over an existing Remote Access Service (RAS) link that you have access rights to, one of the following messages appears after you enter the correct password:

  • From File Manager:
    Stop. Access has been denied.
  • From MS-DOS Command Prompt:
    Error 5: Access has been denied.
These symptoms occur after you call a RAS server from your RAS client and the RAS server authenticates you successfully. Your RAS connection is not affected when the above error messages appear.

CAUSE

Your local logon credentials differ from your remote domain credentials or, if they do not differ, you are not logged on to Windows for Workgroups.

How RAS Logon and Network Logon Differ

The RAS server does not log you on to the remote domain with your user account, password, and domain credentials you enter in the RAS Authentication dialog box. The remote domain controller only uses these credentials to verify that you have permission to physically access the network as a dial-in client.

NOTE: The RAS Authentication dialog box only appears if you are not logged on to Windows for Workgroups, or if you are calling a RAS server from your RAS client for the first time. If you are not prompted by this dialog box, RAS uses the credentials you enter during your very first RAS call.

To validate your access to protected resources on the remote domain, the remote domain controller checks the credentials you enter when you log on locally to Windows for Workgroups.

Therefore, if your local logon credentials differ from the remote domain credentials, or if you are not logged on locally, you cannot access protected resources on the remote domain and one of the messages above appears.

RESOLUTION

To gain access to your remote resources:

  • Log on to the remote domain after you establish the RAS connection. -or-

  • Automatically log on remotely when you start Windows for Workgroups (before the RAS link is established).
These solutions are explained below. They assume that the remote domain administrator has previously granted you access rights to the share you are trying to connect to.

Log On to the Remote Domain After You Establish the RAS Connection

To log on to the remote domain after you establish the RAS connection, or after you log on locally, enter your remote domain name in Control Panel Network and then log off and on again:

  1. Run Control Panel and choose Network.
  2. Choose Startup.
  3. Select "Log On To Windows NT Or LAN Manager Domain".
  4. Enter the remote domain name in the Domain Name field and choose OK.

    NOTE: Making the local domain name identical to the remote domain name is a security issue. Check with your administrator before changing it.
  5. Choose OK again.
  6. From the Program Manager Network group, run Log On/Off to log off.

    NOTE: Logging off does not hang up your RAS connection.
  7. Run Log On/Off again to log on with your remote user name and password.
If the symptoms still occur, and you are sure you are supplying correct credentials, check with your network administrator to determine if you have access permissions to the remote share.

Automatically Log On Remotely at Windows for Workgroups Startup

(Before the RAS Link is Established)

To configure Windows for Workgroups and RAS so you do not have to log on, make your local user account, password, and domain name credentials the same as your remote domain credentials.

NOTE: Making the local domain name identical to the remote domain name is a security issue. Check with your administrator before changing it.

If you cannot make your credentials the same (due to your network configuration), you can still avoid logging off and on again after each RAS connection. To do so, run Control Panel to enter your remote domain name so you can use your remote domain credentials when you are logging on during startup of Windows for Workgroups (even though the RAS connection does not exist yet):

  1. Run Control Panel and choose Network.
  2. Choose Startup.
  3. Select "Log On To Windows NT Or LAN Manager Domain".
  4. Enter the remote domain name in the Domain Name field and choose OK.

    NOTE: Making the local domain name identical to the remote domain name is a security issue. Check with your administrator before changing it.
  5. In the Microsoft Windows Network dialog box choose Log Off.

    NOTE: Logging off does not hang up your RAS connection.
  6. If your remote user name is different from your local user name, type your remote user name in the Default Logon Name field and choose OK.
  7. Quit Windows for Workgroups and reboot your computer.
  8. Start Windows for Workgroups and enter your remote user name and password in the logon dialog box.

    NOTE: A message appears stating that you are logged on. Your remote domain credentials are now cached for automatic use when you later connect over RAS to your protected resources on the remote domain.

    Ignore the part of the message that indicates there was no server to log you on. This message is expected because the remote domain controller cannot be reached for account validation until you have a RAS connection.
Each time you log on with your remote credentials when you start Windows for Workgroups, you will be able to establish the RAS connection and connect to your protected remote resources without having to log off and on again.

NOTE: Logging on with your remote credentials may prevent you from accessing local resources and browse lists because your remote credentials may not be valid on your local network. For more information, contact your network administrator.
Modification Type:MajorLast Reviewed:10/29/1999
Keywords:KB131659
©2002 Microsoft Corporation. All rights reserved.